well.. it's 12:39AM
30 min ago i was out in the dark and cold measuring the @$$ to 77"!

boy i need a big wing






edit to original post-
this thread was meant to be one of those long never ending 'conversation' threads. In the title '..today?!' means the day you are viewing/entering a post.

What's magic about 77"?

Mine needs wash / detail but probablywon't get it unless I go right now.

Instead, I'm watching Ronin - best car chase scenes ever!

well fender to fender on the Z32 @$$ is about 70".

add a couple fender flares and it jumps to @77".

most wings available are only 59".

the APR GT500 is 70" but is also listed at $1400.00.

'F' THAT!!

I guess I've never measured my @$$.

why do you need a wing?

what did i do to my Z today? just drove it about a mile. yesterday, absolutely nothing, but bought her some nice presents.

well when this was posted i pulled my hicas system completely out of the car. Removed the passenger side head and dissassembled it to the valve springs. freed the driver side head but got stuck on the dipstick so it seems ill be pulling my motor today but on the bright side the installs i am planning on doing will be hella easier this way.

WHAT you may ask am i doing? Well 5 angle valve job and port match on the heads and also a port match on the upper and lower intake plenum. ARP head studs and GREX metal head gaskets. Replacing all the exhaust and intake gaskets, complete egr delete, replace all rubber hoses with sylicone ones, chrome balance tube, chrome NA power steering reservoir and complete hicas delete, including the na power steering pump swap. stainless steel bolt kit for plenum. Mike Smith exhaust manifolds to top it all off. new plugs uhhh new turbo gaskets AGAIN new intake filters and gunna fab in the flower pot mod. pcv either delete or re route. oh yea and pulling out all the pipeing and cleaning all the oil out that has accumulated in the intake.

any comments about the pcv delete or re route please post them i want to know the pros and cons of it all. thanks

put gas in it ...lol

put the new spoiler on and replaced all the wipers.

TODAY i got the mofo running right!!!!!

well... running 'rightER' anyway.

ol duct tape on the filter temporary mod

WTF

Ah, forgot all about the dual intake!

It's always something, but at least I don't have to pull the motor...

Since the weather's been so nice, I took the Z out of hibernation for some mid winter enjoyment. After doing a bit of driving, I noticed the smell of hot oil when I got out of the car, and said to my self... Oh no! Not Again! Well it wasn't the oil pump this time, thank goodness, but damn it's tough to get at little things when they're not positioned just right in this car.

The little hose clamp seen in the pix below needed to be tightened. With the motor in the car, good luck getting a wrench or socket on it when it's oriented as it is in these pix. It may be a bit more of a hassle when the motor is out, but if the screw-head is towards the out-side of the car and facing down, it'll be a whole lot easier to get to with the motor in the car.





And on Saturday I put the cat-pipes on so I can get it inspected.

yikes Barry. that sure would suck. i hate those style clamps. i wish all of mine were Tbolt style clamps.

JDMZ32 wrote:

why do you need a wing?

because i dont have anything really helping push down the rearend of my car.

plus its time to make the car more track oriented.

good reason.

wow reid, you're busy! so, you doubt you'll be back next month - is this why?

today i tested out the new flower pots and started boost leak testing.

http://www.zenthusiast.net/fourth-gen-300zx-z32-f1/boost-leak-check-t516.htm#5709

yes that is one of the reasons. The other is im still not done with the usmc. Anyway, Decided to go ahead and pull the motor and do a basic build ie

wiseco pistons and rings
arp rod bolts, main and head studs
racing bearings
knife edged crank
bored rear coolant for 5 and 6 pistons to improve coolant
and of course the head work i listed earlier as well as the coolant upgrades

today i freed the motor but it was raining most of the day so i couldnt finish the pull but tomorrow i will be dropping the tranny (its already free) and then out she comes
then i will proceed to pull her apart and take the parts to be machines to the machine shop and get to cleaning everything ive torn out